Follow Us
Price | RM31.23 RM104.10 |
Product SKU | EEP4767 |
Brand | Raspberry Pi |
Points Needed | 4950 |
Availability | In Stock |
Quantity |
|
Description
Highlight
- Walk-In Price: RM104.00
- Warranty: 12 Months (T&C Apply)
- Plug & Play
- PoE IEEE 802.3at
- Class 4 device
- Output Power: 5V DC / 4A
- Power: 25.5W
- Compatible with Raspberry Pi 4 & 3B+
Note: Raspberry Pi Board and Ethernet cable are not included.
You can click below link to add-on
- Raspberry Pi 4 Model B (8GB)
- Raspberry Pi 4 Model B (4GB)
- Raspberry Pi 4 Model B (2GB)
- Raspberry Pi 3 Model B+
DESCRIPTION
The Raspberry Pi PoE+ HAT is an add-on board for Raspberry Pi computers with PoE pins, including Raspberry Pi 3B+ and Raspberry Pi 4. It is used to power Raspberry Pi via an Ethernet cable, provided that power-sourcing equipment is installed on the Ethernet network. The HAT also includes a fan that will cool the Raspberry Pi processor.
COMPARISON - POE HAT VS POE+ HAT
Features | PoE | PoE+ |
---|---|---|
Standard | 802.3af | 802.3at |
Device Class | 2 | 4 |
Input | 36 - 56V DC | 37 - 57V DC |
Output Voltage | 5V DC | 5V DC |
Max Current | 2.5A | 4A |
Max Power | 15.4W | 25.5W |
Current Sense | No | Yes |
Power Supply | Fully isolate Switched-Mode Power Supply (SMPS) | Fully isolate Switched-Mode Power Supply (SMPS) |
Transformer | Wire wound | Planer |
Cooling Fan | Yes | Yes |
PCB | 4 layer 2oz | 4 layer 2oz |
FEATURES
- Plug & Play
- Power over Ethernet IEEE 802.3at compliant
- Class 4 device
- Fully isolate Switched-Mode Power Supply (SMPS)
- Input Voltage: 37 - 57V
- Output Voltage: 5V
- Max current: 4A
- Fan Control
- Cooling
- 25 x 25mm
- 2.2 CFM
- Operating Temperature: 0°C to +50°C
- Compatible with
MECHANICALS
- PoeE+ HAT is the same physical size as the current PoE HAT
- Sam max Z-Height from PCB TOP to highest component (fan)
- Has components on both side of the board
- Some (third party) cases that relied on the placement of components and fan may not accommodate the new board
DIMENSION
DOCUMENTS
REMARK
- Only be connected to a Raspberry Pi via the four PoE pins.
- Any external power-sourcing equipment/power injector used to enable an Ethernet network shall comply with relevant regulations and standards applicable in the country of intended use.
- The case should not be covered if used inside a case.
- The connection of incompatible devices to the GPIO connection of a Raspberry Pi computer may affect compliance and result in damage to the unit and invalidate the warranty.
- All peripherals used with this product should comply with relevant standards for the country of use and be marked accordingly to ensure that safety and performance requirements are met. These articles include but are not limited to keyboards, monitors and mice when used in conjunction with Raspberry Pi computers
- Where peripherals are connected that do not include the cable or connector, the cable or connector must offer adequate insulation and operation in order that the relevant performance and safety requirements are met
PACKAGE INCLUDES
- 1 x Power Over Ethernet Plus (PoE+) HAT for Raspberry Pi 4 & 3B+
- 1 x Bolt and Spacer pack
Reviews (0)
view all
back
What's in the box
- 1 x Power Over Ethernet Plus (PoE+) HAT for Raspberry Pi 4 & 3B+
- 1 x Bolt and Spacer pack