FREE SHIPPING to Peninsular Malaysia for orders over RM39.00
Sort by
Show result
  • Operating Voltage : DC12V, 0.16A
  • 5 Blade Design 
  • Good air flow & Low noise
  • Weight : 0.011 kg (with screw)
  • Dimension : 3.00 x 3.00 x 1.2(cm)
  • Material: Nylon 
  • Material: Cold Steel
  • Diameter: 20mm
  • Width: 10mm
  • Colour: White
  • High quality aluminum heatsink/heat sink holder
  • For 12mm laser modules like 12mm red, green and IR laser modules
  • Help to cool the laser to prolong the working time of laser mdoules
  • For the Xboard Relay and Romeo - an Arduino Robot Control Board
  • Transparent acrylic panels looks crystal clear and clean
  • Two different choise for different hobbies
  • Basic version is a atable base
  • Special version is more eye-catching
  • High quality aluminum heatsink/heat sink holder
  • For 10mm laser modules
  • Inner diameter of this one is 10.5mm
  • Two bolts on the top to fix the laser
  • 1045 Propeller
  • Color: Black
  • Material: Plastic
  • Fit for DJI 1045 F380 F450 F550 Quadcopter
  • Coated with silver to make it fully conductive
  • Each order ships with three inches of BOTH halves
  • Its easily sewn or cut
  • Use it to connect various electronics onto clothing projects
  • Made from Stainless Steel Fibers
  • Resistance: 28 Ohms/ft
  • Material : 12UM Stainless steel fiber
  • Gram Weight:0.2458g/m
  • Strength:2.8KGF
  • Perfect for DIY project
  • low cost Red Laser Diode in Copper Casing
  • Can be used to connect diode tubes for multiple use
  • An innovative programming/testing tool
  • Solves the problem of prototyping wearable projects with ICSP and FTDI interfaces in limited spaces
  • Provides 2x4 pogo-pins function-board
  • Supports extension so you can design your own dedicated function-board to meet your specific requirements
  • Operating Voltage: 12VDC
  • Latch Stroke: 0 - 10mm
  • Power On - Retract (Unlock)
  • Power Off - Extend (Lock)
  • 5-12VDC and the stainless steel fibers in this heating fabric will warm up
  • Creating a little heating pad
  • One hand just a gigantic resistor
  • Other hand is flexible, light, and can be wrapped around a project
  • Designed for portable wearable heating pads
  • Mounting hole diameter: 3.5mm

  • Mounting hole pattern: Square 15.8mm (along the length) x 23.8mm (along the width)

  • Fits lasers with up to 12.2mm diameter

  • A sheet of flex PCB material
  • The stuff used to make flexible circuits
  • Raw and unetched
  • Pyralux is the brand name of Dupont's flex PCB material
  • Used in cell phones and other small circuits
  • Power supply: +5V
  • Working current: 25μA
  • Working temperature: -25~125℃
  • Detectable wall thickness: 1~13mm(0.40"x5.12")
  • Conductive liquid/film
  • Coating on a flexible plastic (PET) sheet
  • LCD/OLED manufacture
  • ITO layer on one side
  • Plated with real Silver and super luxe 
  • Use small pieces on the tips of gloves 
  • In any soft circuit situation where you need a bit of stretch
  • Resistance of less than 1 ohm per foot 
  • Used to make soft keypads and capacitive touch sensors, as well as soft "squeeze" switches
  • 63% cotton, 35% silver yarn and 2% spandex
  • Use small pieces for soft switches, plush keypads, capacitive touch sensors, and other textile interfaces
  • Very soft and matte, perfect for ironing onto wearables with double sided interfacing
  • Different resistance in each direction
  • Comprised of a single strand of fiber that travels back and forth across the fabric
  • Working Temperature: 0℃ - 40 ℃
  • Motor voltage: 12VDC
  • Motor current: 200-300mA
  • Flow rate: up to 100 mL/min
  • 100% brand new with high quality
  • Timing can be changed to be suitable for different brushless motors
  • The maximum current can reach 25A
  • Full protection features: low voltage cut-off protection /over-heat protection /throttle signal lost protection
  • Throttle range can be configured to provide best throttle linearity, fully compatible with most market available transmitters
  • Model : STARS-922
  • Thermal conductivity : > 0.671 W/m-k
  • Thermal resistance : < 0.06 Celsius Degrees -in2/W
  • Small and light, convenient for use. 
  • Designed specifically for energy production. 
  • Sealed to protect against moisture and contain elements formulated for Optimal thermal energy generation Seebeck. 
  • High reliability and no pollution. 
  • Product structure and composition.
  • Router/ Laser Cut Suitable
  • Easy to Machine, Fabricate & Thermoform
  • Excellent Sound Insulation Properties
  • Outstanding Light Transmission
  • Multipurpose use
  • Material: Acrylic 
  • Type: Transparent color
  • Thickness: 3 ± 0.2mm
  • Optical clarity
  • 99% UV resistant
  • FTDI FT232RL USB to serial IC
  • Aiming development between computer and microcontroller, 3.3V or 5V logic
  • USB powered, no external source is required to use this converter
  • 5V from USB port is available for the user
  • Configurable for 3.3V/5V UART interface
  • Plug and Play
  • CH340 USB to UART chip.
  • Low cost yet easy to use USB to UART converter.
  • Aiming development between computer and microcontroller, 3.3V or 5V logic.
  • EPCglobal Gen2 and ISO/IEC 18000-6c
  • 800 Bits of Memory
  • 512 User Bits
  • EPCglobal Gen2 and ISO/IEC 18000-6c
  • 800 Bits of Memory
  • 512 User Bits
  • Compatible with Windows XP, Vista, 7, 8 and 8.1.

  • Compatible with Microchip’s PICkit 2.

  • Powered directly from USB port.

  • NO EXTERNAL POWER REQUIRED for UIC00B to function.

  • Compatible with PICkit2's Logic Tool and UART Tool.