Charger
FREE SHIPPING to Peninsular Malaysia for orders over RM39.00
Dear valued customer. In line with the MCO 2.0 introduced by government, we will be disable self-collection service start from 21/1/2021 until further notice. But no worry, you still can place your order from our online store. All orders will be ship out via courier service. Stay home and Shop safely.
Charger
Sort by
Show result
  • Stackable shield to Arduino compatible platforms, enables adaptive battery power and act as energy harvester for in-field charging
  • The maximum current provided by the board can get up to 600mA
  • Short circuit protection
  • Continuous Charge Current Up to 900mA
  • Micro-USB Connector
RM69.50
  • Single Cell Lithium based battery charger.
  • USB Micro B connector for power input
  • 5V input pads for DIY/custom input.
  • Input Voltage: 5VDC
RM5.00
  • Input Voltage: 110-240VAC
  • Display: 3x Bicolour LED
  • Charging Current: 700mA
RM49.00
  • Output: DC 8.5V 1.5A
  • Interface: DC 2.1mm (Female/Male) (Arduino compatible)
  • Led Indicator: Red (charging), Green (charged), Green Flash (protection mode triggered)
  • Support Battery: 7.4V Lipo Battery (2-cell pack)
RM52.50
RM75.00
  • Comes assembled and tested with a free bonus JST cable!
  • 5V input via PCB-style USB connector
  • For charging single Lithium Ion/Lithium Polymer 3.7/4.2v batteries (not for older 3.6/4.1v cells)
  • 100mA charge current, adjustable to 500mA by soldering a jumper closed
  • Free 2-pin JST cable included!
RM34.00
  • Comes assembled and tested with a free bonus JST cable!
  • 5V input via Mini-B USB connector
  • For charging single Lithium Ion/Lithium Polymer 3.7/4.2v batteries (not for older 3.6/4.1v cells)
  • 100mA charge current, adjustable to 500mA by soldering a jumper closed
RM45.00
  • Model: HX-3S-01
  • Upper Operating Current: 8A
  • Charging Voltage: 12.6V - 13V
RM8.99
  • Internal 110-240V AC switch power.
  • Compact and light balance charger for 2 to 3 cells of Li-Po battery.
  • High precision balance circuit can supply balanced current up to 850mA per cell.
RM25.90
  • Output voltage at 5.1 to 5.2VDC
  • Input voltage: 6V to 24VDC
  • Maximum output current at 3A, 2.1A continuous.
  • Low voltage ripple at 10mV.
RM8.00
  • Input Voltage: AC100-240V 50/60Hz
  • Charging Voltage: DC4.2V 1000mA x 2
  • Slot Size: 18650 x 2
RM16.00
  • Input Power: Micro USB DC 5V 2A
  • Output Voltage: 1.42V, 4.2V±0.05V, 3.65±0.05V, 4.35±0.05V
  • Output Current: 500mA / 1000mA
  • USB Port Output Load Voltage: 4.90-5.30V
  • Constant Voltage Charging, Cutoff Current: <100m A
  • Output Current: 1000mA
RM30.00
  • Programmable Charge Current:Up to 1000mA
  • Constant-Current/Constant-Voltage
  • Types of battery:Single-cell Li-Ion or Li-Polymer batteries
RM49.00
  • AC input: 100-240Volt
  • DC input: 11-18Volt
  • Circuit power: Max.charge power 50W
  • Max.discharge power 5W
RM120.00
  • Model: MTLC-04200-1000
  • Input Voltage: 100-240VAC 50/60Hz
  • Charging Voltage: 4.2VDC 1A
  • Slot Size: 1 x 18650 
RM9.00
  • Input Voltage: 4.4 ~ 6V
  • Charging Current: 500mA Max (Depending on the solar battery supply capability)
  • Charging Cutoff Voltage: 4.2V
RM24.90

Note: This version uses a micro-USB cable. We also have this charger with a mini-USB connection as well.

FEATURES

  • 29.4x10.8mm
RM42.50
  • Comes assembled and tested, includes a JST cable!
  • 5V input via mini-B USB connector
  • For charging single Lithium Ion/Lithium Polymer 3.7/4.2v batteries (not for older 3.6/4.1v cells)
  • 500mA charge current, adjustable from 100mA to 1000mA by soldering in a resistor
  • Separate JST connectors for battery and load system so batteries don't have to be removed for charging
RM65.00