Charger
- Stackable shield to Arduino compatible platforms, enables adaptive battery power and act as energy harvester for in-field charging
- The maximum current provided by the board can get up to 600mA
- Short circuit protection
- Continuous Charge Current Up to 900mA
- Micro-USB Connector
RM69.50
- Single Cell Lithium based battery charger.
- USB Micro B connector for power input
- 5V input pads for DIY/custom input.
- Input Voltage: 5VDC
RM5.00
- Input Voltage: 110-240VAC
- Display: 3x Bicolour LED
- Charging Current: 700mA
RM49.00
- Output: DC 8.5V 1.5A
- Interface: DC 2.1mm (Female/Male) (Arduino compatible)
- Led Indicator: Red (charging), Green (charged), Green Flash (protection mode triggered)
- Support Battery: 7.4V Lipo Battery (2-cell pack)
RM52.50
RM75.00
- Comes assembled and tested with a free bonus JST cable!
- 5V input via PCB-style USB connector
- For charging single Lithium Ion/Lithium Polymer 3.7/4.2v batteries (not for older 3.6/4.1v cells)
- 100mA charge current, adjustable to 500mA by soldering a jumper closed
- Free 2-pin JST cable included!
RM34.00
- Comes assembled and tested with a free bonus JST cable!
- 5V input via Mini-B USB connector
- For charging single Lithium Ion/Lithium Polymer 3.7/4.2v batteries (not for older 3.6/4.1v cells)
- 100mA charge current, adjustable to 500mA by soldering a jumper closed
RM45.00
- Model: HX-3S-01
- Upper Operating Current: 8A
- Charging Voltage: 12.6V - 13V
RM8.99
- Internal 110-240V AC switch power.
- Compact and light balance charger for 2 to 3 cells of Li-Po battery.
- High precision balance circuit can supply balanced current up to 850mA per cell.
RM25.90
- Output voltage at 5.1 to 5.2VDC
- Input voltage: 6V to 24VDC
- Maximum output current at 3A, 2.1A continuous.
- Low voltage ripple at 10mV.
RM8.00
- Input Voltage: AC100-240V 50/60Hz
- Charging Voltage: DC4.2V 1000mA x 2
- Slot Size: 18650 x 2
RM16.00
- Input Power: Micro USB DC 5V 2A
- Output Voltage: 1.42V, 4.2V±0.05V, 3.65±0.05V, 4.35±0.05V
- Output Current: 500mA / 1000mA
- USB Port Output Load Voltage: 4.90-5.30V
- Constant Voltage Charging, Cutoff Current: <100m A
- Output Current: 1000mA
RM30.00
- Programmable Charge Current:Up to 1000mA
- Constant-Current/Constant-Voltage
- Types of battery:Single-cell Li-Ion or Li-Polymer batteries
RM49.00
- AC input: 100-240Volt
- DC input: 11-18Volt
- Circuit power: Max.charge power 50W
- Max.discharge power 5W
RM120.00
- Model: MTLC-04200-1000
- Input Voltage: 100-240VAC 50/60Hz
- Charging Voltage: 4.2VDC 1A
- Slot Size: 1 x 18650
RM9.00
- Input Voltage: 4.4 ~ 6V
- Charging Current: 500mA Max (Depending on the solar battery supply capability)
- Charging Cutoff Voltage: 4.2V
RM24.90
Note: This version uses a micro-USB cable. We also have this charger with a mini-USB connection as well.
FEATURES
- 29.4x10.8mm
RM42.50
- Comes assembled and tested, includes a JST cable!
- 5V input via mini-B USB connector
- For charging single Lithium Ion/Lithium Polymer 3.7/4.2v batteries (not for older 3.6/4.1v cells)
- 500mA charge current, adjustable from 100mA to 1000mA by soldering in a resistor
- Separate JST connectors for battery and load system so batteries don't have to be removed for charging
RM65.00