Arduino Shields
FREE SHIPPING to Peninsular Malaysia for orders over RM39.00
Shields
Shields
Sort by
Show result
  • Base Shield is to help you getting rid of bread board and jump wires
  • Can add all the grove modules to the Arduino Uno very conveniently
  • 16 grove connectors

 

 

RM43.00
  • Supply voltage:4.5-35V
  • Output voltage:1.25-12V 
  • Output current: 2A (3A peak)
  • Max output power: 15W 3A@5V
  • Efficiency:90%
RM82.00
  • VM Motor Power Supply: 2.5 V ~ 13.5 V
  • VCC Logic Power Supply: 2.7 ~ 5.5 V
  • Output Current: 1.2A continuous current (per channel)
  • Start/Peak Current: 2A (continuous pulse) / 3.2A (single pulse)
  • Working Temperature: -20 ~ 85 ℃
RM69.50
  • Voltage: +5V
  • 16 digital IO port (including a I2C interface)
  • 6 analog IO port and power
  • Operation and programming mode switch
  • Transceiver indicating LED
  • DB9 connectors (female), RS232 pins
RM48.00
  • Power module: +5V
  • Module size: 55mmx53mm(2.16"x2.08")
  • 16 digital IO port (including a I2C interface)
  • 6 analog IO port and power
  • Operation and programming mode switch
  • Transceiver indicating LED
  • Standard RS485 interface, mini RS485 interface and RS485 pins
  • PH2.0 sensor interface for DFRobot RS485 series sensor: URM04 Ultrasonic sensor
RM55.00
  • Allows for motor control with Arduino right away
  • Uses L298P chip which allow to drive two 7-12V DC motors with maximum 2A current
  • Can be directly mounted onto standard Arduino Uno and Arduino Mega
  • Strongly encouraged to use external power supply to power the motor shield
  • Ideal for building Arduino robot or other Arduino motor control projects
RM69.50
  • 128x64 OLED Screen
  • Buzzer, RGB LED
  • DHT11 Temperature&Humidity Sensor
  • 1.5A Relay
  • Helical Potentiometer
  • Mini Joystick
RM115.00
  • 12 capacitive touch sensors
  • Detecting when a person (or animal) has touched one of the sensor electrodes
  • 12 'figure 8' holes
RM75.00
  • I2C-controlled PWM driver with a built in clock.
  • 5V compliant
  • 6 address select pins
RM109.00
  • Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
  • Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping.
  • Motors automatically disabled on power-up
RM129.00
  • Can run off of any Lithium Ion or Lithium Polymer battery (3.7/4.2V kind)
  • Plug in the battery and recharge it via the microUSB jack
  • The onboard boost converter can provide at least 500mA current
  • The shield comes as a kit of parts, some light soldering is required to attach the stacking headers and switch
RM110.00
  • It has a nice standard 0.1"x0.1" prototying grid with big pads
  • Comes with Stacking headers and plain header, choose whichever you want when soldering together
  • A IC pattern for adding DIP ICs up to 20 pins
  • Power rails down the middle and sides
  • A reset button and an extra general use button
RM55.00
  • -165 dBm sensitivity, 10 Hz updates, 66 channels
  • Low power module - only 20mA current draw, half of most GPS's
  • Assembled & tested shield for Arduino Uno/Duemilanove/Diecimila/Leonardo (not for use with Mega/ADK/Due)
RM249.00
  • Can play any uncompressed 22KHz 16bit (on a 12bit DAC), mono Wave (.wav) files of any size.
  • While it isnt CD quality, it is certainly good enough to play music, have spoken word, or audio effects.
  • Output is mono, into L and R channels, standard 3.5mm headphone jack 
RM125.00
  • On-board BLE chip: TI CC2540
  • Wireless Programming via BLE
  • Support Bluetooth HID
  • Support AT command to config the BLE 
  • Transparent communication through Serial
RM135.00
  • AT command to debug the BLE
  • support the master-salve machine switch
  • Transparent transmission
  • Wireless programming for Arduino processor (Compatible with Arduino UNO,Fio and Mega)
  • support usb update BLE chip program
  • support bluetooth HID
RM54.50
  • CAN v2.0B up to 1 Mb/s
  • High speed SPI Interface (10 MHz)
  • Standard and extended data and remote frames
  • CAN connection via standard 9-way sub-D connector
  • Power can supply to Arduino by sub-D via resettable fuse and reverse polarity protection.
  • Socket for EM506 GPS module
  • Micro SD card holder
  • Connector for serial LCD
RM125.00
  • 4-Axis support
  • Runs on 12-35V DC depend stepper driver
  • GRBL V1.1 compatible
RM10.00
  • Implements CAN V2.0B at up to 1 Mb/s
  • Operating Voltage: DC5-12V
  • SPI Interface up to 10 MHz
  • Ariduino/ Freaduino Completely compatible
  • Standard (11 bit) and extended (29 bit) data and remote frames
RM53.50
  • Seperate 3.3V voltage regulator for WROOM-02 module, 500mA max output
  • 802.11 b/g/n
  • Support Wi-Fi Direct (P2P), soft-AP
  • Integrated TCP/IP protocol stack
  • Integrated TR switch, balun, LNA, power amplifier and matching network
RM49.90
  • Controller: W5100
  • Can be used as server or client
  • Directly plug puzzle board, no soldering required
  • Directly supported by Arduino official Ethernet Library
RM28.00
  • Onboard Microcontroller: ATmega32u4
  • Arduino Leonardo Chip
  • Arduino Compatible pin mapping
  • Compatible with All arduino standard shield and sensors
  • System Voltage: 5v
RM99.80
RM105.00
  • Designed to attach a Beetle
  • For easy connecting servos and sensors
  • Directly stack the Beetle onto the Beetle Shield
  • Some soldering will be needed for reinforcement
RM14.50
  • Support most of the Arduino shield
  • DIP prototyping area makes it easy to add more chips or electronic components
  • 3 Xbee slots
  • 1 microSD slot
  • Power selector to select between DFrduino Mega power or external power
RM65.00
  • 14 I/O Pin (servo type with GND, power and signal)
  • 8 analog Pin with power output and GND
  • 6 PWM Pin
  • 1 Servo power input
  • I2C expansion Pin
RM12.50
  • Compatible with the new Arduino Due
  • 3.3V/5V operating voltage select
  • Switch for wireless communtcation & programme
  • More Easily recognitive interfaces
RM59.00
  • Can drive 2 stepper motors or 2 Servo or 4 DC motors.
  • 2 interface for 5V Servo connected to the for Arduino's high-resolution dedicated timer - no jitter.
  • Up to 4 bi-directional DC motors with individual 8-bit speed selection.
RM12.50
  • L298P Motor Driver
  • Dual H Bridge driver
  • Motor Control : 2 Way Channel
  • Input Voltage : 6.5 -12V
  • Max Current : 2A
RM26.50
  • Compatible with any Arduino UNO R3 "alike" board.

  • Design to be used with Lipo type of battery.

  • Start up maximum continuous current at 700mA

  • Maximum continuous current 1000mA

  • Over current cutoff: ~1100mA

RM55.00
  • High Receiver Sensitivity: down to -146 dBm
  • TX Power: adjustable up to +14 dBm high efficiency PA
  • FSK, GFSK, MSK, GMSK, LoRa and OOK modulation
RM99.00