
Shields
- Base Shield is to help you getting rid of bread board and jump wires
- Can add all the grove modules to the Arduino Uno very conveniently
- 16 grove connectors
RM43.00
- Supply voltage:4.5-35V
- Output voltage:1.25-12V
- Output current: 2A (3A peak)
- Max output power: 15W 3A@5V
- Efficiency:90%
RM82.00
- VM Motor Power Supply: 2.5 V ~ 13.5 V
- VCC Logic Power Supply: 2.7 ~ 5.5 V
- Output Current: 1.2A continuous current (per channel)
- Start/Peak Current: 2A (continuous pulse) / 3.2A (single pulse)
- Working Temperature: -20 ~ 85 ℃
RM69.50
- Voltage: +5V
- 16 digital IO port (including a I2C interface)
- 6 analog IO port and power
- Operation and programming mode switch
- Transceiver indicating LED
- DB9 connectors (female), RS232 pins
RM48.00
- Power module: +5V
- Module size: 55mmx53mm(2.16"x2.08")
- 16 digital IO port (including a I2C interface)
- 6 analog IO port and power
- Operation and programming mode switch
- Transceiver indicating LED
- Standard RS485 interface, mini RS485 interface and RS485 pins
- PH2.0 sensor interface for DFRobot RS485 series sensor: URM04 Ultrasonic sensor
RM55.00
- 128x64 OLED Screen
- Buzzer, RGB LED
- DHT11 Temperature&Humidity Sensor
- 1.5A Relay
- Helical Potentiometer
- Mini Joystick
RM115.00
- 12 capacitive touch sensors
- Detecting when a person (or animal) has touched one of the sensor electrodes
- 12 'figure 8' holes
RM75.00
- I2C-controlled PWM driver with a built in clock.
- 5V compliant
- 6 address select pins
RM109.00
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping.
- Motors automatically disabled on power-up
RM129.00
- Can run off of any Lithium Ion or Lithium Polymer battery (3.7/4.2V kind)
- Plug in the battery and recharge it via the microUSB jack
- The onboard boost converter can provide at least 500mA current
- The shield comes as a kit of parts, some light soldering is required to attach the stacking headers and switch
RM110.00
- It has a nice standard 0.1"x0.1" prototying grid with big pads
- Comes with Stacking headers and plain header, choose whichever you want when soldering together
- A IC pattern for adding DIP ICs up to 20 pins
- Power rails down the middle and sides
- A reset button and an extra general use button
RM55.00
- -165 dBm sensitivity, 10 Hz updates, 66 channels
- Low power module - only 20mA current draw, half of most GPS's
- Assembled & tested shield for Arduino Uno/Duemilanove/Diecimila/Leonardo (not for use with Mega/ADK/Due)
RM249.00
- Can play any uncompressed 22KHz 16bit (on a 12bit DAC), mono Wave (.wav) files of any size.
- While it isnt CD quality, it is certainly good enough to play music, have spoken word, or audio effects.
- Output is mono, into L and R channels, standard 3.5mm headphone jack
RM125.00
- On-board BLE chip: TI CC2540
- Wireless Programming via BLE
- Support Bluetooth HID
- Support AT command to config the BLE
- Transparent communication through Serial
RM135.00
- AT command to debug the BLE
- support the master-salve machine switch
- Transparent transmission
- Wireless programming for Arduino processor (Compatible with Arduino UNO,Fio and Mega)
- support usb update BLE chip program
- support bluetooth HID
RM54.50
- CAN v2.0B up to 1 Mb/s
- High speed SPI Interface (10 MHz)
- Standard and extended data and remote frames
- CAN connection via standard 9-way sub-D connector
- Power can supply to Arduino by sub-D via resettable fuse and reverse polarity protection.
- Socket for EM506 GPS module
- Micro SD card holder
- Connector for serial LCD
RM125.00
- 4-Axis support
- Runs on 12-35V DC depend stepper driver
- GRBL V1.1 compatible
RM10.00
- Implements CAN V2.0B at up to 1 Mb/s
- Operating Voltage: DC5-12V
- SPI Interface up to 10 MHz
- Ariduino/ Freaduino Completely compatible
- Standard (11 bit) and extended (29 bit) data and remote frames
RM53.50
- Seperate 3.3V voltage regulator for WROOM-02 module, 500mA max output
- 802.11 b/g/n
- Support Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
- Integrated TR switch, balun, LNA, power amplifier and matching network
RM49.90
- Controller: W5100
- Can be used as server or client
- Directly plug puzzle board, no soldering required
- Directly supported by Arduino official Ethernet Library
RM28.00
- Onboard Microcontroller: ATmega32u4
- Arduino Leonardo Chip
- Arduino Compatible pin mapping
- Compatible with All arduino standard shield and sensors
- System Voltage: 5v
RM99.80
RM105.00
- Designed to attach a Beetle
- For easy connecting servos and sensors
- Directly stack the Beetle onto the Beetle Shield
- Some soldering will be needed for reinforcement
RM14.50
- Support most of the Arduino shield
- DIP prototyping area makes it easy to add more chips or electronic components
- 3 Xbee slots
- 1 microSD slot
- Power selector to select between DFrduino Mega power or external power
RM65.00
- 14 I/O Pin (servo type with GND, power and signal)
- 8 analog Pin with power output and GND
- 6 PWM Pin
- 1 Servo power input
- I2C expansion Pin
RM12.50
- Compatible with the new Arduino Due
- 3.3V/5V operating voltage select
- Switch for wireless communtcation & programme
- More Easily recognitive interfaces
RM59.00
- Can drive 2 stepper motors or 2 Servo or 4 DC motors.
- 2 interface for 5V Servo connected to the for Arduino's high-resolution dedicated timer - no jitter.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection.
RM12.50
- L298P Motor Driver
- Dual H Bridge driver
- Motor Control : 2 Way Channel
- Input Voltage : 6.5 -12V
- Max Current : 2A
RM26.50
-
Compatible with any Arduino UNO R3 "alike" board.
-
Design to be used with Lipo type of battery.
-
Start up maximum continuous current at 700mA
-
Maximum continuous current 1000mA
-
Over current cutoff: ~1100mA
RM55.00
- High Receiver Sensitivity: down to -146 dBm
- TX Power: adjustable up to +14 dBm high efficiency PA
- FSK, GFSK, MSK, GMSK, LoRa and OOK modulation
RM99.00
- Digital Input/Output: D0-D53
- Analog Input/Output: A0-A15
- Power LED indicator
- Reset button
- With holes for installation
RM25.00