Accessories
- Digital two wire (I2C) interface
- Command-based Reading, Compensated (Optional)
- Ultra-low power consumption
- Altitude Resolution down to 0.01 meter
- Temperature measurement included
RM98.50
- Transmit infrared signals through an infrared LED
- Color centered around 940nm
- Not only to transmit data but also to emulate remotes to control your home appliance using an Arduino
RM16.50
- Type: HJ12864ZW
- Controller: ST7920
- Display color: Blue
- Character color: white
- Other features: 5V logic power supply, parallel communication, high reliability, wide temperature range
RM28.90
- This is a 16x2 LCD Keypad module for ARDUINO / Arduino Diecimila Duemilanove / FREEDUINO board.
Blue Backlight with white words
Uses 4 Bit Arduino LCD Library
RM12.00
- Support development boards such as ArduinoUNO and Mega2560 for use without wiring
- 320X240 HD resolution and support touch function
- Supports 16-bit RGB 65K color display and rich color display
- using 8-bit parallel bus, refresh faster than serial SPI
- With SD card slot to facilitate the expansion of the experiment
RM64.50
- 2 way 7-12V motor drive
- Up to 1A current each way
- PIN 4,5,6,7 are used to drive two DC motors
- Support PWM speed control
RM46.00
- Uses a 128x64 liquid crystal display that support Chinese character, English characters and even graphics
- Suitable for interactive work with Arduino
- A backlit control, pallerlel or serial control, contrast adjust
- Can be connect to our interface shield for arduino via IDC6 socket and Cable for Shiftout
- Default in parallel mode
RM95.00
- Logic level shifter Bi-Directional with 4 channels between high logic voltage and low logic voltage
- Each level converter has the capability of converting 4 pins on the high side to 4 pins on the low side with two inputs and two outputs provided for each side
- This 4 channels bi-directional logic level converter is a small device that safely steps down 5V signals to 3.3V and steps up 3.3V to 5V at the same time
RM2.50
- USB logic analyzer
- For monitoring, analyzing and debugging digital circuits
- 8-Channels USB logic analyzer
- Logical light indication
- USB power supply
RM46.50
- With an ATmega328p chip or SAMD21 or even SAMD51
- This shield will make usage a snap
- Light soldering to attach the headers, connector and terminal block
- Able to attach any RGB matrix with ease
- This shield just takes care of the wiring for you
RM39.00
- Compatible with Arduino UNO, Leonardo, easy to connect with various Arduino shields
- XBee connector for connecting various XBee modules
- Sensor interface for connecting various sensors
- Onboard USB TO UART for serial port debugging, also can be configured as XBee USB adapter
RM85.00
- Wire Type : Single Core
- Total Quantity : 140pcs +-5pcs
- Wire length , 2,5,7,10,12,15,17,20,22,25,50,75,100,125 mm (Each 10pcs)
RM8.00
- Need an external 16MHz crystal or resonator, a 5V supply, and a serial connection
- Atmel’s ATMega328P 8-Bit Processor in 28 pin DIP package.
- It’s like the ATmega168, with double the flash space. 32K of program space. 23 I/O lines, 6 of which are channels for the 10-bit ADC.
RM29.00
- Black character, yellow green backlight
- 5 x 8 dots with cursor
- Built-in controller (KS 0066 or Equivalent)
- + 5V power supply (Also available for + 3V)
- 1/16 duty cycle
RM8.00
- White character, blue backlight
- 5 x 8 dots with cursor
- Built-in controller (KS 0066 or Equivalent)
- + 5V power supply (Also available for + 3V)
- 1/16 duty cycle
RM8.00
- Real-time clock (RTC) to maintain the time, even when the a rduino is unplugged. Backup battery lasted for many years
- Including SD card and RTC libraries and sample code means you can get fast
- Welded joints, circuits or sensors prototyping area.
RM12.90
- Wide voltage range from 3.3V to 5V
- Standard assembling structure (two 3mm holes with multiple of 5cm as interval)
- Easily recognitive interfaces of sensors ("A" for analog and "D" for digital)
- Icons to simplely illustrate sensor function
- High quality connector
- Immersion gold surface
RM15.00
- Interface: I2C
- SDA (DATA) - analog input pin 4
- SCL (CLOCK) - analog input pin 5
- Pin Definition: GND、VCC、SDA、SCL
- Backlight: Blue
- Supply voltage: 5V
RM10.50
- Voltage: 5V
- Interface: I2C
- Backlight: Blue
- Max number of characters: 4 lines x 20 characters
- Quality 2004 LCD screen
RM26.00
- Reverse Voltage: 5V.
- Forward Current: 60mA.
- Forward Surge Current: 3A.
RM1.00
- LCD display module with yellow blacklight
- Wide viewing angle and high contrast
- Display construction: 20 characters x 4 line
RM20.00
- Keep your electronics from going barefoot
- For any electronic kit or device
- They are sticky, but not impossible to remove
- Made of Polyurethane
RM8.00
- Saves a lot of time when we want to connect the I/O pins to the external circuit
- Include a set of these label stickers for pin headers in each of the Maker UNO Plus
- Maker UNO Plus uses the common Micro USB cable which is basically everywhere
RM60.00
- The MicroView is the first chip-sized Arduino compatible module that lets you see what your Arduino is thinking using a built-in OLED display.
- With the on-board 64x48 pixel OLED, you can use the MicroView to display sensor data, emails, pin status, and more.
- It also fits nicely into a breadboard to make prototyping easy.
- The MicroView also has a full-featured Arduino library to make programming the module easy.
RM143.50
RM205.00
- SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card
- Real time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years
- Included libraries and example code for both SD and RTC mean you can get going quickly
- Prototyping area for soldering connectors, circuitry or sensors.
RM79.00
- Dimensions: 2.1" x 3.2"
- Comes with a 16x2 RGB backlight LCD, negative display
- Plug and play with any Arduino 'classic' - UNO, duemilanove, diecimilla, etc as well as Arduino Mega R3.
- Uses only the I2C pins - Analog 4 & 5 on classic Arduinos, Digital 20 and 21 on Arduino Mega R3
- This board/chip uses I2C 7-bit address 0x20
- Mounting hole size is 2.5mm
RM139.00