Arduino Accessories
FREE SHIPPING to Peninsular Malaysia for orders over RM39.00
Accessories
Sort by
Show result
  • Digital two wire (I2C) interface 
  • Command-based Reading, Compensated (Optional) 
  • Ultra-low power consumption 
  • Altitude Resolution down to 0.01 meter 
  • Temperature measurement included
RM98.50
  • Transmit infrared signals through an infrared LED
  • Color centered around 940nm
  • Not only to transmit data but also to emulate remotes to control your home appliance using an Arduino
RM16.50
  • Supported by official Arduino IDE
  • Works well for ATmega168 and ATmega168
  • Suitable for most AVR boards
RM47.20
RM59.00
  • Type: HJ12864ZW
  • Controller: ST7920
  • Display color: Blue
  • Character color: white
  • Other features: 5V logic power supply, parallel communication, high reliability, wide temperature range
RM28.90
  • This is a 16x2 LCD Keypad module for ARDUINO / Arduino Diecimila Duemilanove / FREEDUINO board.
    Blue Backlight with white words
    Uses 4 Bit Arduino LCD Library
RM12.00
  • Support development boards such as ArduinoUNO and Mega2560 for use without wiring
  • 320X240 HD resolution and support touch function
  • Supports 16-bit RGB 65K color display and rich color display
  • using 8-bit parallel bus, refresh faster than serial SPI
  • With SD card slot to facilitate the expansion of the experiment
RM64.50
  • 2 way 7-12V motor drive 
  • Up to 1A current each way
  • PIN 4,5,6,7 are used to drive two DC motors
  • Support PWM speed control 
RM46.00
  • Uses a 128x64 liquid crystal display that support Chinese character, English characters and even graphics
  • Suitable for interactive work with Arduino
  • A backlit control, pallerlel or serial control, contrast adjust
  • Can be connect to our interface shield for arduino via IDC6 socket and Cable for Shiftout
  • Default in parallel mode 
RM95.00
  • Logic level shifter Bi-Directional with 4 channels between high logic voltage and low logic voltage
  • Each level converter has the capability of converting 4 pins on the high side to 4 pins on the low side with two inputs and two outputs provided for each side
  • This 4 channels bi-directional logic level converter is a small device that safely steps down 5V signals to 3.3V and steps up 3.3V to 5V at the same time
RM2.50
  • USB logic analyzer 
  • For monitoring, analyzing and debugging digital circuits
  • 8-Channels USB logic analyzer
  • Logical light indication
  • USB power supply
RM46.50
  • With an ATmega328p chip or SAMD21 or even SAMD51
  • This shield will make usage a snap
  • Light soldering to attach the headers, connector and terminal block
  • Able to attach any RGB matrix with ease
  • This shield just takes care of the wiring for you
RM39.00
  • Compatible with Arduino UNO, Leonardo, easy to connect with various Arduino shields
  • XBee connector for connecting various XBee modules
  • Sensor interface for connecting various sensors
  • Onboard USB TO UART for serial port debugging, also can be configured as XBee USB adapter
RM85.00
  • Wire Type : Single Core
  • Total Quantity : 140pcs +-5pcs
  • Wire length , 2,5,7,10,12,15,17,20,22,25,50,75,100,125 mm (Each 10pcs)
RM8.00
  • Need an external 16MHz crystal or resonator, a 5V supply, and a serial connection
  • Atmel’s ATMega328P 8-Bit Processor in 28 pin DIP package. 
  • It’s like the ATmega168, with double the flash space. 32K of program space. 23 I/O lines, 6 of which are channels for the 10-bit ADC.
RM29.00
  • Black character, yellow green backlight
  • 5 x 8 dots with cursor
  • Built-in controller (KS 0066 or Equivalent)
  • + 5V power supply (Also available for + 3V)
  • 1/16 duty cycle
RM8.00
  • White character, blue backlight
  • 5 x 8 dots with cursor
  • Built-in controller (KS 0066 or Equivalent)
  • + 5V power supply (Also available for + 3V)
  • 1/16 duty cycle
RM8.00
  • Real-time clock (RTC) to maintain the time, even when the a rduino is unplugged. Backup battery lasted for many years
  • Including SD card and RTC libraries and sample code means you can get fast
  • Welded joints, circuits or sensors prototyping area.
RM12.90
  • Wide voltage range from 3.3V to 5V
  • Standard assembling structure (two 3mm holes with multiple of 5cm as interval)
  • Easily recognitive interfaces of sensors ("A" for analog and "D" for digital)
  • Icons to simplely illustrate sensor function 
  • High quality connector
  • Immersion gold surface
RM15.00
  • Interface: I2C
  • SDA (DATA) - analog input pin 4
  • SCL (CLOCK) - analog input pin 5
  • Pin Definition: GND、VCC、SDA、SCL
  • Backlight: Blue
  • Supply voltage: 5V
RM10.50
  • Voltage: 5V
  • Interface: I2C
  • Backlight: Blue
  • Max number of characters: 4 lines x 20 characters
  • Quality 2004 LCD screen
RM26.00
  • Reverse Voltage: 5V. 
  • Forward Current: 60mA.
  • Forward Surge Current: 3A. 
RM1.00
  • LCD display module with yellow blacklight
  • Wide viewing angle and high contrast
  • Display construction: 20 characters x 4 line
RM20.00
  • Keep your electronics from going barefoot
  • For any electronic kit or device
  • They are sticky, but not impossible to remove
  • Made of Polyurethane


 

 

RM8.00
  • Saves a lot of time when we want to connect the I/O pins to the external circuit
  • Include a set of these label stickers for pin headers in each of the Maker UNO Plus
  • Maker UNO Plus uses the common Micro USB cable which is basically everywhere

 

RM60.00
  • The MicroView is the first chip-sized Arduino compatible module that lets you see what your Arduino is thinking using a built-in OLED display.
  • With the on-board 64x48 pixel OLED, you can use the MicroView to display sensor data, emails, pin status, and more.
  • It also fits nicely into a breadboard to make prototyping easy.
  • The MicroView also has a full-featured Arduino library to make programming the module easy.

 

RM143.50
RM205.00
  • SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card
  • Real time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years
  • Included libraries and example code for both SD and RTC mean you can get going quickly
  • Prototyping area for soldering connectors, circuitry or sensors.
RM79.00
  • Dimensions: 2.1" x 3.2"
  • Comes with a 16x2 RGB backlight LCD, negative display
  • Plug and play with any Arduino 'classic' - UNO, duemilanove, diecimilla, etc as well as Arduino Mega R3.
  • Uses only the I2C pins - Analog 4 & 5 on classic Arduinos, Digital 20 and 21 on Arduino Mega R3
  • This board/chip uses I2C 7-bit address 0x20
  • Mounting hole size is 2.5mm
RM139.00